Inseego 5G Wavemaker FX2000 Optimization Guide

However, if you have line of sight to the nearest tower, we recommend using a MIMO log periodic antenna kit instead. The higher gain on these antennas can often get you better performance, but only when you have a straight shot to the tower.

Option #2: Optimize the Inseego FX2000 Location (if band B42, B448, and/or n78 are NOT available)

If bands B42, B448, and/or n78 are NOT available at your location, a MIMO External Antenna kit unfortunately can't provide you with a boost in performance.

However, there is still hope for improving the performance of your Inseego FX2000! Here are the best steps for optimizing the position of your Inseego FX2000 within your home:

1. Look up your nearby towers. This can be time consuming and difficult to get right - we've listed our suggestions in an article on the Best Ways to Locate Nearby Cell Towers
2. Run speed tests with your Verizon Internet Gateway at the windows closest to each nearby tower (If you have multiple floors, perform this process on each floor).
3. Place your Inseego FX2000 at the location with the fastest data speeds.

This process is simple but effective if you haven't already optimized the position of your Inseego FX2000, however this method will likely provide only a small improvement to data speeds compared to Option #1.

Why External Antennas Are Critical for Improving Data Rates

There's one big misconception about external antennas.

Most people think that external antennas primarily help you increase your data rates by increasing the signal strength but that's not the case.

An increase in signal strength is often a less important way that external antennas help.

Here are the two main ways that external antennas help you increase your data rates:

1.They Improve Signal Quality

In 4G LTE and 5G networks, signal quality is measured as SINR (Signal to Interference plus Noise Ratio) or sometimes as RSRQ (Reference Signal Received Quality).

Improving signal quality has a huge impact on your data rates.

Higher data rates allow your hotspot to communicate using "higher order modulation schemes." That means they can use the same wireless spectrum to send more data per second.

However, there's one big caveat: In order to improve your signal quality, you need to both aim and shield your outdoor antenna properly. We talk more about this in the next section.

2.They Increase Your Signal Strength

In 4G LTE and 5G networks, signal strength is measured as RSRP (Reference Signal Received Power).

As you might expect, using outdoor directional antennas can help increase the signal strength. This helps increase data rates, but only up to a point.

If your signal strength (called "RSRP" in LTE and 5G networks) is stronger than about -100 dBm, stronger signal won't speed up your connection any further.

Positioning and Aiming MIMO Antennas

Positioning and aiming MIMO antennas well is crucial to getting the best performance from your Inseego FX2000, or indeed any other hotspot.

We've actually compiled a detailed instruction manual to accompany our own MIMO Antenna Kits, where we go into depth on the best ways to aim the antennas.

The goal is to find the best location and direction for the antenna(s), to maximize data rates to the Inseego FX2000. It can take a little patience, but can have a huge impact – it’s worth a bit of extra effort!

Before getting started, it's always a good idea to run a couple of speed tests indoors from a device connected to your Inseego FX2000's WiFi. The results will fluctuate a little, but this is the baseline you're trying to improve.

Now connect the 4x4 MIMO antenna(s) to your Inseego FX2000 via the four TS9 ports hidden under the two external antenna tabs labeled "1" and "2" and go outside with your "test-rig". If you have a 2x2 MIMO Antenna Kit you will only connect your adapters to the two TS9 ports hidden under the left tab labeled "1".

With each location and direction you try, run a couple speed tests, and make a note of the results. Here are all the locations and directions where we recommend testing your MIMO antenna:

Pro tip: Don’t just go to the highest point of the roof! While signal is generally stronger the higher you go, there’s also often more interference. We’ve found it’s often better to mount the antenna(s) on the side of the building where the structure can shield the antennas from interference.

Once you've found the position which gets you the highest data rates to the Inseego FX2000, that's where you'll want to install the MIMO antenna. Go ahead and mount the antenna, run cables inside, connect everything up, and enjoy superior data rates!

Inseego Wavemaker FX2000 Technical Specifications

NOTE: The Inseego 5G Wavemaker FX2000 ONLY supports bands B42, B48, and n78 for use with external antennas. Please consult your carrier to verify these bands are supported and available at your location prior to purchasing any external cellular antenna equipment.

Supported Cellular Bands (for external antenna use)

Wavemaker FX2000 (T-Mobile)

• 4G LTE: B48

Wavemaker FX2000 & Pro FX2000e (Unlocked)

• 4G LTE: B42, B48
• 5G: n78

Supported Cellular Bands (for internal antenna use only)

Wavemaker FX2000 (T-Mobile)

• 4G LTE: B2, B4, B5, B12, B25, B26, B41, B46, B48, B66, B71
• 5G: n2, n25, n41, n66, n71

Wavemaker FX2000 & Pro FX2000e (Unlocked)

• Supported 4G LTE bands
  • AT&T: B2, B4, B5, B12, B14, B17, B29, B30, B46, B66
  • Verizon: B2, B4, B5, B13, B48, B66
  • T-Mobile: B2, B4, B5, B12, B25, B26, B41, B66, B71
  • Other: B1, B3, B7, B8, B11, B18, B19, B20, B21, B28, B32, B38, B39, B40, B42, B46
• Supported 5G bands
  • AT&T: n5
  • Verizon: n2, n5, n40, n66
  • T-Mobile: n41, n71
  • Other: n1, n3, n7, n8, n12, n25, n28, n38, n40, n46, n48, n77, n78, n79, n83

Cellular Modem

• Model: Qualcomm Snapdragon x55
• MIMO Support: 4X4 w/ internal antennas, 4X4 w/ external antennas
• LTE Performance Category: Cat 20 for FX2000 (T-Mobile), Cat 22 for FX2000 & Pro FX2000e (Unlocked)

Wi-Fi

• Technologies: WiFi 6 - 802.11 a/b/g/n/ac/ax
• Bands: Simultaneous 2.4 GHz and 5.0 GHz

Ports

• Cellular Antenna Ports: 4x TS9
• SIM (4FF Nano) Ports: 1x SIM for FX2000, 2x SIM for Pro FX2000e
• Other Ports: 1x 1 Gbps LAN; 1x USB 3.1 Type C

NOTE: Wavemaker (FX2000) vs Wavemaker Pro (FX2000e)

The key difference between these two Wavemaker models is that the Wavemaker Pro has "Dual SIM" support for (2) Nano 4FF SIM cards. This allows the Wavemaker Pro to have multi-carrier support with auto-switching.

Other Helpful Resources

Inseego 5G Wavemaker Pro FX2000 Announcement Video